📞 Call for Free Quote — (407) 922-9857
Paver SealingWinter Park, FL
A paver seal is a full restoration, not a quick spray. We deep-clean your brick and concrete pavers, strip failing sealer where it's needed, and re-sand every joint with fresh silica. Then we seal them to help hold the color against oak-tannin staining and UV fade, firm up the joints against weeds and ants, and make it harder for algae to take hold in the canopy shade. Historic-district driveways and walkways, lakefront patios and pool decks — done in the right order, every time.
Why Seal Pavers Under the Oak Canopy
Helps Hold the Color
Oak tannin, UV, and the damp under the canopy bleach unsealed pavers gray and blotchy. A quality sealer shields the pigment and helps hold that just-installed color longer.
Resists Shade Algae
Deep shade and lake humidity keep pavers damp, so green film returns fast on an unsealed surface. A sealed, non-porous face gives the algae far less to grip.
Fewer Weeds & Ant Hills
Fresh sand locked under sealer hardens the joints, which helps reduce weeds, ant hills and the joint washout on sloped, brick-paved lots.
Protects Your Investment
Left unsealed, pavers wash out, shift, and sink until they need full re-leveling. We generally recommend evaluating pavers for resealing every 2 to 3 years; the right interval depends on traffic, sun and weather exposure, drainage, sealer condition and overall wear. Resealing costs a fraction of tearing out and re-laying the whole surface.
Get a Free Quote
Response within 1–3 business hours — no pressure, no obligation.
✓ No spam. We only use your info to reach you about your quote.
Why Winter Park Homeowners Trust Us With Their Pavers
A paver seal isn't a spray-and-go; most of the job happens before the sealer comes out. Seal over dirty, damp, or washed-out pavers and you trap in the very stains, oak-tannin haze, and weeds the sealer is supposed to lock out. So we do it in the right order every time: deep clean the surface and strip failing sealer where it's needed, re-sand the joints, let everything dry, then seal.
Sealing over a surface that was only rinsed locks the problem in. We start with a pre-treatment that lifts the built-up grime and kills the organic growth in the pavers and down in the joints, instead of leaving that to water pressure. Then we pressure wash the surface, which takes the weeds and loose debris with it. The pavers have to dry fully before anything goes on top — typically the following day or as weather conditions allow — and only then do we re-sand the joints and apply the sealer. Cleaning, sand and seal are one job done in the right order, not a coat of sealer over a quick rinse.
We're owner-operated, based in Kissimmee, and we regularly serve Winter Park, so we already know these streets — the deep oak shade, the brick-paved historic blocks, the lakefront lots that stay damp off the Chain of Lakes. We seal for what our sun, tannin, and shade actually do to pavers, not a brochure, and we respect the appearance standards the historic district and the associations hold you to. We're licensed and fully insured in Florida, we have 150+ five-star Google reviews, and every paver job is backed by our satisfaction guarantee.
What Makes Us Different:
- We re-sand every joint before sealing — the sealer goes down over full joints, not washed-out gaps
- We neutralize efflorescence and lift oak-tannin staining first, so the staining is dealt with before the sealer goes down
- We match the sealer to your surface — concrete, brick, and travertine each need a different product
- We help you pick matte or wet-look before we ever open a bucket
- Tell us your historic-district or HOA appearance standards and we'll work to them, with before-and-after photos for the board if you need them
Need the pavers or concrete cleaned but not sealed? See the full hard-surface range on our pressure washing in Winter Park. We also do driveway cleaning and pool deck cleaning here, and you can see every city we cover on our service areas page.
Property Assessment & Firm Quote
In most cases, we can price your pavers remotely without scheduling an onsite estimate. We’ll pull the real measurements and ask about the paver type, the condition of the joint sand, and any efflorescence or staining, then provide a firm quote for cleaning, sand and sealer — usually within 1–3 business hours.
If we can’t accurately assess the property remotely, we’ll arrange an onsite visit. Once your quote is approved, your price won’t change unless the scope of work changes.
Pre-Treatment Application
Weeds, tannin, and organic growth get a targeted pre-treatment so they lift in the wash instead of staining under the new sealer. Oil and rust staining is treated separately as a restoration add-on when it is identified and quoted ahead of the job. Old failing sealer is stripped, and efflorescence is neutralized before anything else.
Surface Cleaner Pressure Wash
An industry-grade rotary surface cleaner strips the pavers evenly — no zebra striping — and pulls the old, washed-out joint sand out of the gaps. On travertine and softer stone we drop the pressure and take extra care.
Edge Detailing & Rinse
Borders, steps, and the seams against the house, walkways, and pool coping get hand-detailed, then the whole surface is rinsed clean and left to dry completely — trapped moisture is a common cause of a hazy, milky seal.
Re-Sand the Joints
We sweep fresh silica joint sand into every gap and pack it to depth. Full, stabilized joints help keep the pavers from shifting on sloped lots and make weeds and ant hills far harder to take hold.
Apply the Sealer & Cure
The step that changes everything. Once the surface is clean, re-sanded, and bone-dry, we apply your chosen finish — matte or wet-look — in even coats with a breathable sealer matched to your pavers. Cured, it helps preserve the color, reduce tannin and UV fading and stabilize the joint sand, and beads off water. We give you exact walk-on and drive-on times before we leave.
Every paver job we do is backed by our satisfaction guarantee. If something within the agreed scope was missed or isn't up to our standard, we'll come back and make it right.
Wet Look vs. Matte (Natural) Finish
With your Winter Park pavers cleaned and re-sanded, all that's left is choosing the finish. Both finishes are designed to protect the surface, so the right choice comes down to the look you prefer and the character of your home.
Matte (Natural) Finish
A natural, low-sheen finish that protects your pavers without making them look glossy. It gently deepens the color of brick and stone while keeping the quiet, classic look that belongs on Winter Park's historic, tree-lined streets.
- True-to-brick appearance, with none of the glossy coating
- Brings out the color quietly, with no glare
- A timeless, understated look that suits a historic home
- A restrained finish that sits comfortably in an established neighborhood
- Complete sealing protection while staying easy on the budget
Wet Look (Glossy) Finish
A wet-look sealer deepens the natural color of your pavers and adds a smooth, glossy finish. It gives weathered brick and stone a richer, freshly restored appearance while still respecting Winter Park's traditional style.
- A noticeably richer, deeper paver color
- That just-sealed wet sheen, without the heavy gloss
- A freshly restored, upscale look
- Adds real presence to driveways and entry walkways
- A finish that lifts the appearance of the entire home
Both finishes are designed to protect the surface. Matte and wet-look sealers help repel water, oil, and spills, stabilize the joint sand, reduce weed and algae growth, and extend the life of your pavers. It comes down to the appearance you prefer and your budget.
Pavers & Surfaces We Clean and Seal in Winter Park
Every common paver and stone surface across the area — matching the right pressure and the right sealer to each material.
Concrete Pavers
The most common paver on local driveways and lanais, and quick to gray out under the oaks. Takes a matte or wet-look sealer beautifully once the efflorescence is cleared.
Brick & Clay Pavers
The classic look on the historic blocks around Park Avenue and Interlachen. We strip the old joint sand, re-sand, and seal to help hold the color and stabilize the joint sand against washout.
Historic-District Walkways
Front walks and courtyards where appearance standards are strict. A clean, re-sand, and understated matte seal keeps them looking maintained without changing the character.
Lakefront Patios
Estate patios on Lake Osceola, Lake Virginia, and Lake Maitland that stay damp and algae-prone. Sealed and re-sanded, they shed the green film and the leaf-tannin staining.
Travertine Pool Decks
Soft, cool-underfoot natural stone on lakefront pool homes. Cleaned at low pressure and sealed with a penetrating sealer that soaks in and breathes — never a glossy film.
Sloped Paver Driveways
The brick-paved slopes toward the lakes lose joint sand fastest in a storm. Re-sanding and sealing helps the joints stay full and the pavers stay put, and fewer weeds come up.
Results That Speak For Themselves
What Homeowners Say About Our Paver Work
"Outstanding service. We are blown away by the professionalism, level of service, attention to detail, and the price was affordable! We will absolutely hire again and let everyone know they have to go with AB Superior Wash paver cleaning — you won't regret it!"
"Very professional and reasonably priced! Will definitely recommend!"
"Professional, fast, and reliable. Worked with my budget and delivered excellent results. Great communication, attention to detail, and overall an awesome experience."
Areas We Seal Pavers In & Around Winter Park
Brick on the historic blocks off Park Avenue, concrete pavers out toward Aloma, travertine decks on the lakefront estates — different surfaces, same clean-re-sand-seal job.
32789
32789
32789
32789
32789
32789
32792
32792
Paver Sealing Winter Park FAQ
What homeowners and property managers ask us before we seal, from Park Avenue to the Chain of Lakes.
How much does paver sealing cost in Winter Park?
Why should I seal my pavers instead of just cleaning them?
Should I choose a matte or a wet-look sealer?
How long does paver sealer last in Winter Park's sun and shade?
Do you re-sand the joints before sealing my pavers?
How do you protect landscaping during paver sealing?
Why Pavers Fade and Wash Out Under Winter Park's Oaks
Sealing is only the last of three stages, and it's only as good as the prep under it. First we pressure wash the pavers, adjusting the pressure to the material, and pull out the old joint sand along with any failing sealer, efflorescence and weeds. Oak-tannin staining gets a targeted treatment as part of the cleaning; set-in oil or rust staining is a separately priced restoration add-on that we identify and quote before the job. Then we re-sand the joints. Only once the surface is clean, re-sanded, and fully dry do we seal. Seal over washed-out joints and the pavers stay loose; seal over a damp surface and you can lock a milky haze under a film that's hard to undo. That order matters.
This town is hard on pavers in a way most of Central Florida isn't. The live-oak canopy that shades the brick-paved streets keeps hardscape damp and blotchy with algae year-round, and the falling leaves and Spanish moss drop tannins that stain unsealed pavers a dull brown. Where the sun does reach — open driveways and lakefront pool decks — UV bleaches the color out fast. And on the sloped, brick-paved lots toward the Chain of Lakes, the afternoon downpours flush the sand out of open joints faster than almost anywhere, which is why the pavers start to shift and the weeds and ant hills move in. Re-sanding with fresh silica and locking it under sealer helps prevent both, and we pack the joints to depth instead of just topping them off. For the technical side, the Concrete Masonry & Hardscapes Association, the industry body that absorbed the old Interlocking Concrete Pavement Institute, publishes guidance on cleaning, sealing and joint sand for interlocking pavers.
Winter Park is really several paver jobs in one. The historic district off Park Avenue and around Interlachen needs restraint and consistency — brick walkways kept clean and uniform for the appearance standards, usually finished in an understated matte so nothing looks out of character. The lakefront estates on Lake Osceola, Lake Virginia, and Lake Maitland bring the work right to the water's edge, where a wet-look seal makes a patio or pool deck pop. And out toward Aloma and Goldenrod, newer concrete-paver driveways were often never sealed at all, so within a year or two the color's fading and the joints are emptying out. A fairly new surface is the best time to seal, before the stains set in. You choose the finish, and we match the sealer to the material: concrete and brick take either matte or wet-look, while travertine and natural stone get a penetrating sealer that soaks in and breathes rather than a glossy film. Humidity affects how long a sealer takes to cure, so we'll give you the cure-time instructions for the specific sealer used on your project. When you're ready for the rest of the hardscape, pair it with our driveway cleaning and pool deck cleaning — or see the full Central Florida service area.
AB Superior Wash371 Bald Cypress Dr, Kissimmee, FL 34744
Phone: (407) 922-9857
Hours: Monday–Sunday, 7:30 AM – 8:00 PM
Written by Alejandro Garcia — Owner, AB Superior Wash · (407) 922-9857 · Open every day, 7:30 AM–8:00 PM
Last updated: July 2026
Ready For Sealed, Like-New Pavers?
Deep-cleaned, re-sanded, and sealed against the oak tannin, UV, and shade — Park Avenue to the Chain of Lakes.
